ruthart
سؤال: how big is the diameter on the hole
السؤال بواسطة BG782340512 على 2021-04-30 11:34:44
ruthart The hole is 5mm diameter.
2021-04-30 12:52:47 مساعدة (0)سؤال: Does this board have a programmer on board?
السؤال بواسطة trypesdg على 2021-03-28 08:22:52
ruthart It has a boot loader. If you write a program in the Arduino IDE or PlatformIO you can upload it through the USB port.
2021-03-28 09:12:48 مساعدة (0)سؤال: How bad is the backlash on these?
السؤال بواسطة Bgsto على 2021-02-23 08:36:59
ruthart Backlash is undetectable. But keep in mind that there is a 64 times speed reduction gear inside so it is quite slow.
2021-02-24 07:05:03 مساعدة (1)سؤال: Will it work with tmc2208 stepper driver?
السؤال بواسطة BG531791042 على 2021-02-16 12:49:09
ruthart Yes. Go to reprap.org and check out the wiki info for this board.
2021-02-16 01:50:29 مساعدة (0)سؤال: Is it suitable to be used for a DIY 3d printer?
السؤال بواسطة R0203 على 2021-01-13 10:12:08
ruthart Yes, probably the best choice.
2021-01-13 11:21:26 مساعدة (0)سؤال: WHAT HOSE SIZE ARE THE INLET & OUTLET ???
السؤال بواسطة BG171125920 على 2020-07-04 12:14:40
ruthart The thread is 0.5 inch pipe thread (od 20mm 14 threads per inch). the id is 12 - 13mm.The best fit is probably 0.5 inch hose.
2020-07-05 09:42:43 مساعدة (0)سؤال: What is the current draw of this magnet
السؤال بواسطة BG161715491 على 2020-06-17 01:03:45
ruthart According to the specs 110mA.
2020-06-18 11:31:14 مساعدة (0)
ruthart Use a knife with a strong blade and pry it open at the corners. You have to apply some force but I was able to open it. The LED is next to the battery area.
2020-05-15 10:28:02 مساعدة (0)سؤال: What stepper motor will this work with?
السؤال بواسطة ancsvc على 2020-05-06 01:21:20
ruthart Any nema 17 stepper will work. You don't need high torque.
2020-05-06 08:34:18 مساعدة (0)
ندعوك بصدق للاشتراك في البريد الإلكتروني Invite Answer!
إذا قمت بالاشتراك ، فسندعوك عبر البريد الإلكتروني للإجابة على الأسئلة التي يطرحها الأشخاص حول المنتجات. باشتراكك] سوف تكسب أيضًا "شارة مفيدة "! يمكنك إلغاء الاشتراك في أي وقت على صفحة إعدادات الخصوصية.
ساعد الآخرين وكن أكثر سعادة!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
ruthart It generates a signal which can be used by your main board if so equipped. It would stop the print, record the position and sound the alarm. You may have to modify the firmware for this to work.
2021-09-24 07:06:50 مساعدة (0)