Tom E
Tom E@Roman Potapov Itcomes with an extra long spring and they made it easy to swap springs, so 266650's, 21700's, and even 18650's can be used.
سؤال: What is the head diameter measurement?
السؤال بواسطة Tom E على 2020-08-13 08:54:13
Scottybman Offing not show
2020-09-06 03:36:24 مساعدة (0)
Tom E Sorry,didn't see these comments. I swapped the driver to a FET 1 runing NarsilM, and swapped the LED's to XPL HI V2 5D's - now it's a great light! Draws 9.3 amps max at the tail, does about 2400 lumens at turn on, 2150 at 30 secs and 16 kcd (250 meters) in throw, plus has a great beam, great tint as the HI 5D's do. I just rcv'd a 2nd AX3 and the button doesn't feel as good as the first, but the LED's don't get stuck on very low. I'll see what goin on with the switch - might be alignment, something simple. I have spares that may fit.
سؤال: How many modes of operation does it have and does it have a strobe mode?
السؤال بواسطة donmccoy على 2019-02-20 07:05:56
Tom E As the author of the firmware, the primary default mode is smooth ramping with 150 unique steps that ramp in about 2.4 seconds. In addition though, there are 12 groups of pre-defined mode sets, if that's what you prefer, but most people prefer the ramping once they've used it. There are strobe modes though - if you are at max/turbo, a double-click will display an intense strobe. So from OFF, you can dbl-click, then dbl-click again to get to strobe.
2019-02-22 07:27:44 مساعدة (1)
Tom E Mine is now doing 25.2K @start, 21K at 30 seconds. I added bypass wires on all 5 springs though, removed those blocking tabs around the batt+ contacts, few other minor tweaks but left the stock driver and FET. I used the VapCell 2800's which are VTC5D rewraps - bout the best cell for this light. Stock the light hit 20K lumens at start. Something is wrong there - what cells are you using? You must use high quality, high power cells.
2018-10-27 02:39:47 مساعدة (4)
Tom E Weird - I don't see what you are talking about. Many AR coatings can be noticed by reflection of a purple color, this is how I can verify AR coatings. So, not sure exactly where you see the problem. Inside the glass doesn't matter - only thing that matters is the beam.
Tom E Try a factory reset - it might have gotten disabled -- I've seen/heard it happen several times before.
Tom E My readings were more like 5,300 to 5,500, so we went with listing it at 5,000 lumens. On the recommended Samsung 30Q BT's you should definitely get at least 5,000.
Tom E You can attach a lanyard by using the tripod mount to install a loop. Several types available - I got a bunch. Think I mostly bought them on Ali. Some are a bit too long, so I had to grind them down a little.
ندعوك بصدق للاشتراك في البريد الإلكتروني Invite Answer!
إذا قمت بالاشتراك ، فسندعوك عبر البريد الإلكتروني للإجابة على الأسئلة التي يطرحها الأشخاص حول المنتجات. باشتراكك] سوف تكسب أيضًا "شارة مفيدة "! يمكنك إلغاء الاشتراك في أي وقت على صفحة إعدادات الخصوصية.
ساعد الآخرين وكن أكثر سعادة!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
