كل الرسائل

RuBoy69 2018-05-25 19:42:02
0
التوصيات
تعليقات (0)

كبار المراجعين:

RuBoy69 2018-05-25 19:42:02
0
التوصيات
تعليقات (0)

كبار المراجعين:

RuBoy69 2018-05-25 19:42:01
0
التوصيات
تعليقات (0)

كبار المراجعين:

سؤال: can you explain how it works? What do you need to do practically to use the object?

السؤال بواسطة Iano Renna على 2018-05-01 01:26:00

RuBoy69 It is basically a volt meter. The different lights turn on when it detects different voltages (the item description lists the lights and voltage ranges) across the terminals (marked "+" and "-" on the board). To add this to a completed circuit or project,,, just have a small line from the positive of your battery and one from your negative side, and send it to this device. It just needs to detect the voltage-- you cannot pass voltage through it to power your device, if that makes sense.

2018-05-25 04:17:17 مساعدة (0)
عرض
أجابات (1)

سؤال: Can this be used with a Li-ion battery too ?

السؤال بواسطة Axolotroll على 2018-01-12 10:00:42

RuBoy69 Yes. Li-Po and Li-ion cells have the same voltage ranges and charge/discharge characteristics. You can also use the same chargers, as long as you have the same number of cells and the correct "nominal" voltages.

2018-05-25 04:01:23 مساعدة (0)
عرض
أجابات (2)

سؤال: i want to use this for 6 S (12V) but you only have options up to 4S. How to use with 6S ?

السؤال بواسطة dwainsworld على 2018-01-15 01:40:16

RuBoy69 The description is assuming you are wiring in a series (the S stands for Series). If you have a combination series/parallel, it is different. If you have 6 cells and you measure 12v, then use the 3S model, because your nominal voltage is going to be 11.1v. 12 volts is normal, so don't worry- your voltage will range from ~10v-12.6v. You simply have 2 3S banks in parallel, so use the 3S version.

2018-05-25 03:57:39 مساعدة (0)
عرض
أجابات (2)

سؤال: Which model should I use for a 3.6V NCR18650B Battery?

السؤال بواسطة Simonv92 على 2018-02-13 06:40:17

RuBoy69 For any single 18650 battery (including yours) or most LiPo batteries, use S1. Use S2, S3, and S4 for 2, 3, and 4 cells in series, respectively. If they are in parallel, just use the one for that nominal voltage (S1=3.7, S2-7.4, and so on).

2018-05-25 03:49:44 مساعدة (0)
عرض
أجابات (3)
RuBoy69 2018-05-25 03:18:08
0
التوصيات
تعليقات (0)

كبار المراجعين:

RuBoy69 2018-05-25 03:18:08
0
التوصيات
تعليقات (0)

كبار المراجعين:

RuBoy69 2018-05-25 03:03:08
0
التوصيات
تعليقات (0)

كبار المراجعين:

RuBoy69 2018-05-25 03:01:48
0
التوصيات
تعليقات (0)

كبار المراجعين:

RuBoy69 2018-05-25 03:01:47
0
التوصيات
تعليقات (0)

كبار المراجعين:

RuBoy69 2018-05-02 04:22:05
0
التوصيات
تعليقات (0)

كبار المراجعين: