كل الرسائل

banggood Someone has already asked this. It i re-badged and you want to search for "fnirsi-1013d user guide".

2020-12-29 06:13:28 مساعدة (0)
عرض
أجابات (2)

سؤال: What is the format of the recorded waveform files? How can I use it on my computer?

السؤال بواسطة pthalin على 2020-10-10 04:57:44

banggood I don't think you can. I have opened these in a hex editor and they look like a raw recording of sorts. Not compressed it seems.Too much work to try and map, but the - - stuff seems interesting.You can recall them and get a screenshot. I have tried opening with Pulseview and the format is not recognised. So it does not look like anything widely used.The files seem too small for the samples required.

2020-10-10 06:24:09 مساعدة (0)
عرض
أجابات (1)

سؤال: Can this microscope be used to check a diamond phono stylus point?

السؤال بواسطة analogdino على 2020-09-01 02:28:05

banggood It should, but note there is a better one available for a little more. I can clearly see the dot imprints of the digits on a crystal oscillator package and this would be the same order of magnitude as the stylus. If you actually want to see wear (!). Maybe spend a little more.

2020-09-01 08:05:54 مساعدة (0)
عرض
أجابات (2)

سؤال: Serial data Analyser is possible (I2C , SPI and other communications)

السؤال بواسطة VIKRANTH على 2020-03-23 10:17:44

banggood No, but logic analyzers are better suited for this, having more inputs. Short UART by eye, maybe.

2020-08-15 03:39:48 مساعدة (1)
عرض
أجابات (3)

banggood 9V - 30V but plan for 11V - 30V. This can only "buck". You should plan to supply 4V over for a healthy margin, and not less than 2V. Answer below suggests 8.4V but it does not hurt to over specify. So expect 9V, but plan for 11V. 30V will be :"open circuit" in full sunshine, not achievable under load. You would have to test on a bench supply to get a better result for each one. And then for efficiency. Altogether about 150W at 7V * 15A * 70% estimated efficiency, and that's not considering the thermals. You already have a suitable panel if this a one to one relationship.

2020-07-12 01:53:24 مساعدة (1)
عرض
أجابات (2)

banggood It may take a few days. It is possible that it has yet to be approved. I could not see my own review for a long time either. It is true these may have old firmware, and the solder may need work, and also that you need to buy 2 to fix the firmware and supply and solder on the slow pins yourself, and buy a 6 pin IDC adapter and supply an extra jumper. But the people buying these can do these things.

2020-07-04 07:15:19 مساعدة (1)
عرض
أجابات (1)

سؤال: Will this work to program the ATTiny45 or 85?

السؤال بواسطة davidmberten على 2019-06-05 10:33:52

banggood It will and even the ATTiny13. Bear in mind you need to run it slow for devices running under 1.5MHz. Use USBAsp (Slow) from the Arduino menu, or -B 64 for avrdude. You can use the Jumper JP3 on the board, but this will mean soldering.

2020-06-20 11:02:10 مساعدة (0)
عرض
أجابات (2)

سؤال: Does it also provide power supply to the connected development board?

السؤال بواسطة mitsos1996 على 2019-06-23 12:55:06

banggood A small board, it can. OK for ATTiny things. You must use the jumper, but it is fitted as shipped.

2020-06-17 03:40:20 مساعدة (0)
عرض
أجابات (2)

سؤال: A tensão máxima de entrada é 24 ou 28V?

السؤال بواسطة ciclomts على 2018-09-29 07:38:18

banggood Specs might be wrong 24V to 28V might be optimistic. Alternatively is it a ripple free 24.000V? Not 12V Batteries?

2020-04-13 06:35:10 مساعدة (0)
عرض
أجابات (4)

سؤال: Is it compatible with ATMEGA328P? Thanks ^^

السؤال بواسطة Daniel Choutka على 2018-03-05 01:08:30

banggood Yes it is. You will need to jumper with Dupont wires or use a 10 to 6 pin adapter if you do not have a 10 pin ISP plug on board. For an Uno your adapter should really be be narrow see item id 1413166.

2020-03-27 09:02:13 مساعدة (0)
عرض
أجابات (2)