كل الرسائل

سؤال: Qual tamanho da área de corte? Tem como aumentar a área de corte?

السؤال بواسطة BG531745838 على 2022-06-09 01:42:02

pattarom The working area is 400x410 mm and can be extended up to 850x410 mm with an optional extension kit (which can be purchased on the Atomstack website)

2022-06-10 12:34:20 مساعدة (1)
عرض
أجابات (1)

سؤال: ela corta a Madeira igual a figura que manda pro computador?e até que espessura de Madeira ela corta?

السؤال بواسطة BG371550343 على 2022-04-27 06:49:26

pattarom As far as I know, someone has successfully cut 6 millimeters of plywood. It needs a lot of passes and a nozzle with compressed air that blows over the cut, otherwise, after a few passes, the wood starts to burn. Atomstack has recently started to sell his mini compressor that comes with adapters for all models of laser cutters and a cutting bed to place below the piece to cut to avoid burning the underneath table.

2022-04-27 07:30:51 مساعدة (0)
عرض
أجابات (2)

سؤال: is it dual channel?

السؤال بواسطة Backstep على 2022-01-23 06:04:45

pattarom No, it is a single channel.

2022-01-23 07:02:36 مساعدة (0)
عرض
أجابات (4)

سؤال: How can I get and restore the original firmware of this device

السؤال بواسطة BG473341013 على 2022-01-11 08:47:29

pattarom You cannot restore original firmware without disassemble the plug invalidating the warranty. Also original firmware is not available for download.

2022-01-11 11:03:50 مساعدة (0)
عرض
أجابات (2)

pattarom Yes, you can connect to Tuya App and you can connect from Internet to the device.

2021-12-08 01:22:34 مساعدة (0)
عرض
أجابات (7)

pattarom Usually any NEMA 17 motor should run flawless. You only must check the connector pins position, because pins position is not a standard between manufaturers. If old motor is not burn, you can use a multimeter set in ohm measurement, to discover where motor coils are connected. To find a coil check what pins give continuity (or zero ohm). Compare the position of the old motor with the new one and modify the cable accordingly, changing the position of the wires in the connector. If the motor rotate in reverse, simply swap, between them, the wires of one of the coils (pratically invert the polarity of one of the two coils).

2021-11-13 02:20:29 مساعدة (0)
عرض
أجابات (1)

سؤال: Have you model with larger Engraving Size, for example 100cm * 100cm?

السؤال بواسطة Bj Nas على 2021-10-02 09:41:40

pattarom Looking into manufacturer website, this is the only size their produce. Seems that all laser engraver models share same structure changing the features.

2021-10-04 01:36:56 مساعدة (0)
عرض
أجابات (1)

سؤال: Will this laser cut jigsaw puzzles?

السؤال بواسطة BG441645121 على 2021-08-09 07:00:37

pattarom With the right drawings, you can cut any shape you want, even a jigsaw.

2021-08-10 03:45:02 مساعدة (0)
عرض
أجابات (2)

pattarom You can adjust power to fit the material thru the software. There are no driver (if we not consider the driver for USB port). The engraver use GRBL standard, there are many program that you can use (for example the free LaserWeb). Istruction manual guide you to use a simplier software GRBL (yes program, protocol and firmware loaded into mainboard have the same name)

2021-07-22 02:29:28 مساعدة (0)
عرض
أجابات (3)

سؤال: Is it applicable for SMD PCB-s?

السؤال بواسطة BG184861713 على 2021-05-27 02:58:37

pattarom Tecnically: yes. You can use a permanent marker to darken a blank PCB and then use the laser to clean the marker areas where copper must be eroded by acid. There are some videos on YT that show this process.

2021-05-27 10:59:47 مساعدة (0)
عرض
أجابات (2)

سؤال: is this efficient for outdoor measurmentjQuery111303441652662832677_1618152263573?

السؤال بواسطة BG156151083 على 2021-04-11 09:45:29

pattarom PCB is exposed, so it isn't suitable to work outdoor. It must be protected from moisture, rain and extreme temperaures

2021-04-11 11:53:56 مساعدة (0)
عرض
أجابات (4)