Kayl Hosken
سؤال: how to change to pal from NST
السؤال بواسطة Kayl Hosken على 2018-07-13 11:55:33
JackDee3 I think you can change that setting in the OSD or with editing software.
2021-11-06 04:57:59 مساعدة (0)سؤال: how do i power the Flight controller, can it be powered by the Vbat terminal connection
السؤال بواسطة Kayl Hosken على 2018-05-04 06:19:28
Martin Kottek Yes, Check out a Wiring Diagram for this FC to locate the pins for Vbat.
2021-11-03 07:26:11 مساعدة (0)سؤال: does this ESC provide 4x 15A out put or is it a total of 15A so 4x3.75A?
السؤال بواسطة Kayl Hosken على 2019-06-08 06:56:31
supriyakhamitkar yes ti provides 4×15A output
2021-02-25 10:19:25 مساعدة (1)سؤال: i need the wiring diagram what each colour wire is please
السؤال بواسطة Kayl Hosken على 2019-03-08 05:21:18
kreidler50 LtR if cable plugged in: black-GND, red-VBat, white-M4, yellow-M3, green-M2, gray-M1
2021-01-16 03:50:36 مساعدة (0)
BG535533421 Mostif not all Flight Controllers have their own 5v regulators onboard, converting VBATT into 5v for the FC to run on. Either a linear regulator or an actual 5v BEC. Check the spec of your particular FC.
2020-10-13 06:31:53 مساعدة (0)سؤال: Can I use with original FC of lizard95? Because I think this don't have bec.
السؤال بواسطة Felipe على 2020-01-11 08:38:19
Kayl Hosken I did this as you said you can and by doing so i blew up my Frsky reciever and VTX..... Connecting this ESC directly to the original FC of lizard95 puts battery voltage to all your 5v pads on the original FC of lizard95. Also other flight controllers the cable harness connects to FC and they are expecting 5v. so check if your FC does take 2-4s battery voltage. Need solder power wires to the correct locations and use a 5v bec with the original FC of lizard95. I found out the hard way
2020-03-01 02:32:45 مساعدة (0)
Kayl Hosken SOit fits the Foxeer HS1177? Im guessing extra 1 in there typo
سؤال: what size are the screws that go into the camera?
السؤال بواسطة Kayl Hosken على 2018-07-07 02:48:44
ethss m2 screw
2018-08-04 12:57:10 مساعدة (0)سؤال: how to change to pal
السؤال بواسطة Kayl Hosken على 2018-07-06 06:04:15
Coburglis02 It is automatically switched according to your camera.
2018-08-02 06:42:52 مساعدة (0)
Lactoscope It doesn't have 5V BEC Output. It is a flight controller board and you want to connect it to another FC? That sounds amazing.
2018-06-04 03:05:23 مساعدة (0)سؤال: sold in pack of four
السؤال بواسطة Kayl Hosken على 2018-03-02 03:28:18
ندعوك بصدق للاشتراك في البريد الإلكتروني Invite Answer!
إذا قمت بالاشتراك ، فسندعوك عبر البريد الإلكتروني للإجابة على الأسئلة التي يطرحها الأشخاص حول المنتجات. باشتراكك] سوف تكسب أيضًا "شارة مفيدة "! يمكنك إلغاء الاشتراك في أي وقت على صفحة إعدادات الخصوصية.
ساعد الآخرين وكن أكثر سعادة!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
