ucfnf
سؤال: can I bind this to my jumper t18?if so whats the protocol?
السؤال بواسطة MRFLYHIGH على 2021-04-08 08:55:13
سؤال: what is the flying control range?
السؤال بواسطة BG173625121 على 2020-11-22 05:43:54
ucfnf The receiver is a RadioLink R8FM. RadioLink says, the control distance is 2000 meters in the air.
2021-03-08 12:44:31 مساعدة (1)سؤال: What's the recommended batt for the hook extra 300-h
السؤال بواسطة BG505034171 على 2021-03-02 07:34:31
ucfnf User manual recommand 4S Li-Po Battery 14,8 V 1500 -2200 mAh.
2021-03-03 12:41:17 مساعدة (1)سؤال: Is there a throttle pinout on this board to use a brushless ESC?
السؤال بواسطة cvflyer على 2021-02-16 08:29:30
ucfnf Sorry no, there are only 2 pinouts to connect and throttle a brushed motor.
2021-02-16 01:20:33 مساعدة (0)سؤال: Can be bind with Jumper T12 ?
السؤال بواسطة popad على 2021-02-06 10:41:17
ucfnf You need the Volantex protocol " V 761". If it´s not supported, try to load it from multi-module.org
2021-02-08 04:58:51 مساعدة (0)سؤال: where can i find more references / study about this?
السؤال بواسطة freecarve على 2021-01-30 02:30:40
ucfnf I think it´s comparable with the Fisher Wallace stimulator, see fisherwallace.com and their product reviews for more information.
2021-01-31 11:59:37 مساعدة (0)سؤال: Do I need to have 2 antennas attached? Can I run it with only 1 antenna?
السؤال بواسطة Tomas على 2021-01-13 05:53:53
ucfnf Yes, it will run with only 1 antenna, I tested it. There is only one receiver inside, which switch to the antenna with the best signal.
2021-01-15 09:49:26 مساعدة (0)سؤال: Is the Razor compatible with a Radiomaster TX16S?
السؤال بواسطة Gilles على 2021-01-07 10:08:23
ucfnf Yes, use the protocol RadLink Air and push the tiny binding switch of the receiver.
2021-01-11 01:01:15 مساعدة (0)سؤال: what transmitters works with the receiver in the RTF
السؤال بواسطة BG441854224 على 2020-09-23 01:21:04
ucfnf The included TX is a RadioLink TX with eachine label. The receiver works also with each TX with Open TX Multi protocol. The protocol is: RadLink Air. The receiver is hidden under the FC. Pull out and push the tiny binding switch for binding.
2021-01-04 09:51:17 مساعدة (1)سؤال: Which protocol is used by the included RX / Tx?
السؤال بواسطة kieber على 2020-11-20 10:37:49
ucfnf Works with OpenTx Multi protocol, latest update:" RadLink Air ". You must pull out the receiver -its under the FC- to push the tiny binding switch. Don´t forget the Fine Tuning.
2021-01-04 09:31:55 مساعدة (0)ندعوك بصدق للاشتراك في البريد الإلكتروني Invite Answer!
إذا قمت بالاشتراك ، فسندعوك عبر البريد الإلكتروني للإجابة على الأسئلة التي يطرحها الأشخاص حول المنتجات. باشتراكك] سوف تكسب أيضًا "شارة مفيدة "! يمكنك إلغاء الاشتراك في أي وقت على صفحة إعدادات الخصوصية.
ساعد الآخرين وكن أكثر سعادة!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
ucfnf It´s a RadioLink receiver and it works with OpenTx Multi protocol, latest update: "RadLinkAir". You must pull out the receiver-its under the FC- to push the tiny binding switch. Don´t forget the Fine Tuning.
2021-04-15 08:15:23 مساعدة (0)