Paul159
سؤال: Can I run it on a 3S Lipo ? If yes, do you recommand a different propeller to get good efficiency ?
السؤال بواسطة Paul159 على 2020-11-11 04:02:44
Paul159 Ican't say if it will work with MircoSD but it does work with MicroSDXC. I have tested it with a Samsung EVO Plus 64GB Class 10, U3 MicroSDXC and a Samsung EVO Plus 128GB Class 10, U3 MicroSDXC and both worked great. Beware, the maximum capacity for these goggles is 128GB.
2021-02-20 08:13:56 مساعدة (6)سؤال: can you use the Fatshark Shark Byte with these goggles?.
السؤال بواسطة JuanDavidMaldonado على 2021-02-08 07:43:12
Paul159 There'san HDMI port on the bottom and it is 720p so you should be able to use is but don't quote me on that.
2021-02-10 09:41:26 مساعدة (0)سؤال: That's work with caddx nebula digital hd system?
السؤال بواسطة BG489748104 على 2021-01-19 05:44:27
Paul159 No,it only works with analog video or via the HDMI or AV port on the bottom.
2021-02-01 01:03:06 مساعدة (0)
Paul159 Maybe,but to me it looks like the ESC is oveheating. It could be reducing the power output to avoid damaging itself.
2021-01-24 02:56:03 مساعدة (0)سؤال: Can it also be used on a motorized glider?
السؤال بواسطة MarcoB على 2021-01-22 10:21:17
Paul159 Yes! You can draw a maximum of 104 Amps from it, connect 7 servos on 5, 6 or 7.2 Volts switchable with a maximum current draw of 6 Amps which should be planty for most gliders under 2.5 meters in wing span.
2021-01-24 02:52:56 مساعدة (0)سؤال: Can a 4s 1300 mah battery fit?
السؤال بواسطة BG373135715 على 2020-12-16 08:48:27
Paul159 Yes but it barely fits, I put a 4s 1300 mAh ZIPPY in mine but it pushed the canopy up a bit and with a flight controller, camera and VTX it was a bit too heavy. If you don't want to put a FC and stuff in it I think it will be alright.
2020-12-17 09:57:21 مساعدة (0)سؤال: will the hero9 fit in the front of this as this camera is a little bit larger than the previous ones
السؤال بواسطة ukdjtaz على 2020-11-09 12:57:27
Paul159 No, you will need to cut a bit of foam to fit it. Hero 6 fits nicely.
2020-11-12 04:31:31 مساعدة (0)سؤال: Does the PNP version come with a folding propeller?
السؤال بواسطة lylesmann على 2020-11-10 03:45:26
Paul159 No
2020-11-11 03:58:05 مساعدة (0)سؤال: is pnp version have servo connecting parts?
السؤال بواسطة kerembp06 على 2020-11-05 12:00:53
Paul159 Yes
2020-11-11 03:57:06 مساعدة (0)سؤال: O esc possui Bec ??
السؤال بواسطة Natan3301 على 2020-04-20 03:39:01
Paul159 Yes, 5V 2A
2020-06-17 07:34:17 مساعدة (0)سؤال: can this be used with out with out needing a programing card
السؤال بواسطة parjacpar على 2019-07-07 05:16:28
Paul159 You can only do a throttle calibration and set the ESC brake On and Off
2020-06-17 07:17:40 مساعدة (1)سؤال: Can it run on 4s ?
السؤال بواسطة Grzegorz Szlag على 2019-04-02 01:12:23
Paul159 It probably can, you just need to make sure you don't draw more current than it's maximum value, otherwise it will heat up too much and the isolation on the windings will come off.
2020-06-17 07:10:27 مساعدة (0)سؤال: what is the amp draw on this when using 1600mw?
السؤال بواسطة Corkers100 على 2019-11-14 04:59:33
Paul159 It draws about 20mA when ran at 14.8 volts with a 4S battery. The current draw is nothing to worry about.
2020-06-17 05:12:52 مساعدة (1)سؤال: Can't find any manual? How to setup the beeper?
السؤال بواسطة Robin Stehmeier على 2018-10-19 09:57:57
Paul159 Connect the first two wires ( black and white ) to the button which is on a small PCB by soldering them, then connect the yellow wire to the buzzer minus pad on your FC ( BUZ- ) and finally connect the red and black wires to a +5V and a GND pad on your FC. These wires are for charging the onboard battery. If the red LED is blinking it meens the Beeper is ON, and if it loses the connection to your FC, ( say you unpluged your FC or it ran out of batterie ) it will start beeping at you after around 10 seconds. To turn off the beeper, simply long-press the button you connected with the black and white wire or the button that is onboard the beeper until the red LED stops blinking. FC : Flight Controller PCB : Printed Circuit Board LED : you know what a LED is no need to explain
2020-06-17 04:59:18 مساعدة (6)ندعوك بصدق للاشتراك في البريد الإلكتروني Invite Answer!
إذا قمت بالاشتراك ، فسندعوك عبر البريد الإلكتروني للإجابة على الأسئلة التي يطرحها الأشخاص حول المنتجات. باشتراكك] سوف تكسب أيضًا "شارة مفيدة "! يمكنك إلغاء الاشتراك في أي وقت على صفحة إعدادات الخصوصية.
ساعد الآخرين وكن أكثر سعادة!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
Sunny2424 28xx motor does not fit. Don’t buy 28xx motor. I bought it big mistake. Only 22xx motor can fit
2021-05-18 07:07:06 مساعدة (4)