استعراضات العملاء

4.94 من 5
أكتب مراجعة
  • كل المراجعات (72)
  • صورة (4)
  • فيديو (0)
  • بداية الكل
    • بداية الكل(72)
    • 5 بدأ(68)
    • 4 بدأ(4)
    • 3 بدأ(0)
    • 2 بدأ(0)
    • 1 بدأ(0)
الترتيب حسب:
أفضل مراجعة
  • أفضل مراجعة
  • الأكثر أفاده
  • آخر
المراجعات من بلدك فقط (Iraq)
  • May-26 2020 00:00:00

    يجب تحسين الحزمة. بعض الدبابيس

    تعليقات
  • November-21 2016 00:00:00

    Despite the small difference in appearance, the device is as as described. Everything works normally. Only problem I had when supplied with 12.14 volts. Although LEDs lit, no output voltage. I suppose that the maximum supply voltage is a little less than 12 volts.

    تعليقات
  • April-26 2018 00:00:00

    Used for Arduino projects - just search for "Arduino L9110S" on Google, and you will find Lib and examples. Even with a "short" on the motor side, I have not been able to "Kill" the board

    تعليقات
  • May-05 2018 00:00:00

    Pretty nice

    تعليقات
  • July-05 2020 00:00:00

    يعمل بشكل رائع، فقط خفض التصنيف لأن التغليف لم يكن جيداً و الدبابيس كانت منحنية.

    تعليقات
  • April-03 2021 00:00:00

    جيده

    تعليقات
  • February-22 2021 00:00:00

    ممتثلة تماماً وبالطبع

    تعليقات
  • March-26 2017 00:00:00

    Tested with a pro mini and worked great. I had to try two different power plug supply's, one was 12.3 volts even though it was labeled as 12 volts and it did not work. It did not damage it but be careful it might. 12 volts might be its absolute max. I will probably use this with a 9 volts just to be safe

    تعليقات
  • March-07 2017 00:00:00

    Just be sure that you check the connections to match them with your circuit. (Vcc, GND, A1A, A1B,etc.) The connecting pins are in a different order than the ones on the controller shown in the diagrams in my project. Not a problem; the controller will work fine when you connect the wires correctly according to the labels printed on the board.

    تعليقات
  • January-31 2016 00:00:00

    This little part has some punch when driving DC motors. I tested both drivers on my robot and they worked like a charm. But after measuring the current, it looks like the HD7881 chips do tend to heat up quite a bit when the load current exceeds ~350mA. Yes, the part is rated for 800mA, so it might make sense to add a small heat sink when dealing /w heavy loads. Otherwise, this is just perfect for small (i.e. light load) projects. I will definitely order more of these parts !

    تعليقات
Show:

    مجموع 0 الصفحات

    انتقل إلى صفحة

    قد تكون مهتمة ايضا بـ

    recommendation for you
    • US$16.99
    • US$5.29
    • US$2.79
    • US$2.15
    • US$2.15
    • US$2.73
    • US$2.15
    • US$1.95
    • US$2.02
    • US$4.25
    • US$4.31
    • US$2.36
    • US$12.99
    • US$24.41
    • US$3.51
    • US$1.64
    • US$13.52
    • US$4.31