Got it and assembled without any problem, however a simple assembly manual may be useful for the non expert (I am a radio amateur, so I am used to build and assembly antennas). It is not clear how to assemble the clamps, however I set them up one in a direction and the second one opposite to the first one and it' s holding. The antenna is now on top of a vertical pole about 4 meters above ground level. The coaxial cable which comes attached with the antenna is quite long, however I didn't measure it (yet); it is branded "SYWU - 50 - 5"; it is pretty rigid and stiff and BNC terminated. The vertical element (and the radials) is made of TWO sections, one screws into the other. The vertical element is 68.5 cm long and the three radials are 72.5 cm long. There are no trees or other man-made structures within at least 3 meters from the antenna. In these testing conditions, I measure the SWR of the antenna with an MFJ-259 Antenna Analizer and I find it is almost perfectly centered on 100 Mhz. At 100 Mhz I measure 1.0 SWR !!! At 101 Mhz SWR is 1.3; at 102 SWR is 1.6 and so on. At 99 Mhz SWR is 1.3 and so on. So, while the antenna does work as expected, if you need to transmit (say) on 88 Mhz) you will need to extend the lenght of the radials and of the vertical element. And that is a problem. If you need to transmit (say) on 105 Mhz you will need to "cut" few CM's of the radials and the vertical element. For AUD 50 including shipment, it's a good buy; if you do not transmit on 100 Mhz, you will need some expertise and instrumentation to tune the antenna to your desired TX frequency. Worth of note is the fact that the vertical elements and the radials are made of two sections; this means that potentially (I haven't tried yet) if I install only ONE element in each, the antenna will be tuned on a much higher frequency, possibly of use for radio amateur frequencies. I will test and comment again. Cheers for now. Stefano Mollo.

Got it and assembled without any problem, however a simple assembly manual may be useful for the non expert (I am a radio amateur, so I am used to build and assembly antennas). It is not clear how to assemble the clamps, however I set them up one in a direction and the second one opposite to the first one and it' s holding. The antenna is now on top of a vertical pole about 4 meters above ground level. The coaxial cable which comes attached with the antenna is quite long, however I didn't measure it (yet); it is branded "SYWU - 50 - 5"; it is pretty rigid and stiff and BNC terminated. The vertical element (and the radials) is made of TWO sections, one screws into the other. The vertical element is 68.5 cm long and the three radials are 72.5 cm long. There are no trees or other man-made structures within at least 3 meters from the antenna. In these testing conditions, I measure the SWR of the antenna with an MFJ-259 Antenna Analizer and I find it is almost perfectly centered on 100 Mhz. At 100 Mhz I measure 1.0 SWR !!! At 101 Mhz SWR is 1.3; at 102 SWR is 1.6 and so on. At 99 Mhz SWR is 1.3 and so on. So, while the antenna does work as expected, if you need to transmit (say) on 88 Mhz) you will need to extend the lenght of the radials and of the vertical element. And that is a problem. If you need to transmit (say) on 105 Mhz you will need to "cut" few CM's of the radials and the vertical element. For AUD 50 including shipment, it's a good buy; if you do not transmit on 100 Mhz, you will need some expertise and instrumentation to tune the antenna to your desired TX frequency. Worth of note is the fact that the vertical elements and the radials are made of two sections; this means that potentially (I haven't tried yet) if I install only ONE element in each, the antenna will be tuned on a much higher frequency, possibly of use for radio amateur frequencies. I will test and comment again. Cheers for now. Stefano Mollo.

Got it and assembled without any problem, however a simple assembly manual may be useful for the non expert (I am a radio amateur, so I am used to build and assembly antennas). It is not clear how to assemble the clamps, however I set them up one in a direction and the second one opposite to the first one and it' s holding. The antenna is now on top of a vertical pole about 4 meters above ground level. The coaxial cable which comes attached with the antenna is quite long, however I didn't measure it (yet); it is branded "SYWU - 50 - 5"; it is pretty rigid and stiff and BNC terminated. The vertical element (and the radials) is made of TWO sections, one screws into the other. The vertical element is 68.5 cm long and the three radials are 72.5 cm long. There are no trees or other man-made structures within at least 3 meters from the antenna. In these testing conditions, I measure the SWR of the antenna with an MFJ-259 Antenna Analizer and I find it is almost perfectly centered on 100 Mhz. At 100 Mhz I measure 1.0 SWR !!! At 101 Mhz SWR is 1.3; at 102 SWR is 1.6 and so on. At 99 Mhz SWR is 1.3 and so on. So, while the antenna does work as expected, if you need to transmit (say) on 88 Mhz) you will need to extend the lenght of the radials and of the vertical element. And that is a problem. If you need to transmit (say) on 105 Mhz you will need to "cut" few CM's of the radials and the vertical element. For AUD 50 including shipment, it's a good buy; if you do not transmit on 100 Mhz, you will need some expertise and instrumentation to tune the antenna to your desired TX frequency. Worth of note is the fact that the vertical elements and the radials are made of two sections; this means that potentially (I haven't tried yet) if I install only ONE element in each, the antenna will be tuned on a much higher frequency, possibly of use for radio amateur frequencies. I will test and comment again. Cheers for now. Stefano Mollo.

This antenna could be paired with 5W FM transmitter sku 103051. For my first trial, the antenna was not enough placed high from the ground. So I could broadcast a radio program in a radius of 2 km. This received signal is perfect in a radius of 500 m. I'm sure I can increase noticeably the range if I place the antenna on the roof of my house.

This antenna could be paired with 5W FM transmitter sku 103051. For my first trial, the antenna was not enough placed high from the ground. So I could broadcast a radio program in a radius of 2 km. This received signal is perfect in a radius of 500 m. I'm sure I can increase noticeably the range if I place the antenna on the roof of my house.

This antenna could be paired with 5W FM transmitter sku 103051. For my first trial, the antenna was not enough placed high from the ground. So I could broadcast a radio program in a radius of 2 km. This received signal is perfect in a radius of 500 m. I'm sure I can increase noticeably the range if I place the antenna on the roof of my house.

Apparently the antenna is of good quality but the coaxial cable is fixed in the base of the antenna without possibility of exchange, has not yet been installed, therefore no possibility of verifying the performance.

Apparently the antenna is of good quality but the coaxial cable is fixed in the base of the antenna without possibility of exchange, has not yet been installed, therefore no possibility of verifying the performance.

Apparently the antenna is of good quality but the coaxial cable is fixed in the base of the antenna without possibility of exchange, has not yet been installed, therefore no possibility of verifying the performance.

I am using this with the 5 watt FM transmitter tuned to 99.9 MHz with it mounted 27 feet up and getting 4 miles range to my vans FM radio. I got less than 3 miles when transmitting on 94.1 MHz. I hope it survives the harsh winter weather we get in North Dakota USA.

I am using this with the 5 watt FM transmitter tuned to 99.9 MHz with it mounted 27 feet up and getting 4 miles range to my vans FM radio. I got less than 3 miles when transmitting on 94.1 MHz. I hope it survives the harsh winter weather we get in North Dakota USA.

I am using this with the 5 watt FM transmitter tuned to 99.9 MHz with it mounted 27 feet up and getting 4 miles range to my vans FM radio. I got less than 3 miles when transmitting on 94.1 MHz. I hope it survives the harsh winter weather we get in North Dakota USA.

هوائي الثاني الذي أشتريه & بشكل عام هو جيد جداً 4 $، العبوة السيئة جداً & مرة أخرى الشحن التالف مثل القضيب الأول يجب أن تكون داخل أنبوب لإيقاف انحناء القضيب.مرة أخرى يجب أن أصلح السفينة إلى كندا لمدة 18 يوماً.

Is 2nd antenna I buy & overall it’s very good 4 the $.Very bad packaging & again shipping damaged like 1st.Rods MUST be inside a tube to stop rod bending.Again I must fix.18 day ship to Canada.

هوائي الثاني الذي أشتريه & بشكل عام هو جيد جداً 4 $، العبوة السيئة جداً & مرة أخرى الشحن التالف مثل القضيب الأول يجب أن تكون داخل أنبوب لإيقاف انحناء القضيب.مرة أخرى يجب أن أصلح السفينة إلى كندا لمدة 18 يوماً.

The antenna is built with quality material, easy to install, but could improve with the connector that you drop from the antenna, because the cable comes fixed in the antenna and has no way to exchange them.

The antenna is built with quality material, easy to install, but could improve with the connector that you drop from the antenna, because the cable comes fixed in the antenna and has no way to exchange them.

The antenna is built with quality material, easy to install, but could improve with the connector that you drop from the antenna, because the cable comes fixed in the antenna and has no way to exchange them.

Avec 5W à 16' de haut je couvre environ 4km de rayon. Constitution très simple. Ce n'est pas très clair ici mais il y a trois radials et DEUX mats d'antenne pour obtenir le meilleur SWR en fonction de la fréquence. À 88,1MHz j'ai 1,2 SWR.

Avec 5W à 16' de haut je couvre environ 4km de rayon. Constitution très simple. Ce n'est pas très clair ici mais il y a trois radials et DEUX mats d'antenne pour obtenir le meilleur SWR en fonction de la fréquence. À 88,1MHz j'ai 1,2 SWR.

Avec 5W à 16' de haut je couvre environ 4km de rayon. Constitution très simple. Ce n'est pas très clair ici mais il y a trois radials et DEUX mats d'antenne pour obtenir le meilleur SWR en fonction de la fréquence. À 88,1MHz j'ai 1,2 SWR.

Waoooo! Muchas felicidades quedó satisfecho con su cumplimiento en tiempo y entrega en hora buena sigan así me despido un cliente conforme con banggodd y su compañía animo no cambien

Waoooo! Muchas felicidades quedó satisfecho con su cumplimiento en tiempo y entrega en hora buena sigan así me despido un cliente conforme con banggodd y su compañía animo no cambien

Waoooo! Muchas felicidades quedó satisfecho con su cumplimiento en tiempo y entrega en hora buena sigan así me despido un cliente conforme con banggodd y su compañía animo no cambien

In specifications it is mentioned that it is of stainless steel material but in actual it is steel only

In specifications it is mentioned that it is of stainless steel material but in actual it is steel only

In specifications it is mentioned that it is of stainless steel material but in actual it is steel only

لطيف

nice

لطيف