los interruptores con correctos, tal como se describen, quizás son un poco pequeños,hacen click correctamente, tiene tres patas para poder usarlo como interruptor doble

los interruptores con correctos, tal como se describen, quizás son un poco pequeños,hacen click correctamente, tiene tres patas para poder usarlo como interruptor doble

los interruptores con correctos, tal como se describen, quizás son un poco pequeños,hacen click correctamente, tiene tres patas para poder usarlo como interruptor doble

here's an example of how I place them in tiny locations... It you have fairy fingers and have to solder with tiny wires, here you go! They are cheap so far, so I would buy them again. But you have to know that I already had to trash two of them, because the mechanics inside won't stand the heating for more than a couple of seconds when soldering. You will have bad contacts and/or the plastic will loosen and let go of the trigger. Just ckeck before closing your machine, and if bad luck, just redo it! I think I could affort that!

here's an example of how I place them in tiny locations... It you have fairy fingers and have to solder with tiny wires, here you go! They are cheap so far, so I would buy them again. But you have to know that I already had to trash two of them, because the mechanics inside won't stand the heating for more than a couple of seconds when soldering. You will have bad contacts and/or the plastic will loosen and let go of the trigger. Just ckeck before closing your machine, and if bad luck, just redo it! I think I could affort that!

here's an example of how I place them in tiny locations... It you have fairy fingers and have to solder with tiny wires, here you go! They are cheap so far, so I would buy them again. But you have to know that I already had to trash two of them, because the mechanics inside won't stand the heating for more than a couple of seconds when soldering. You will have bad contacts and/or the plastic will loosen and let go of the trigger. Just ckeck before closing your machine, and if bad luck, just redo it! I think I could affort that!

Már be is építettem a modellrádiómba és remekül működik.

Már be is építettem a modellrádiómba és remekül működik.

Már be is építettem a modellrádiómba és remekül működik.

Отличние тумблери к Таранис Лайту

Отличние тумблери к Таранис Лайту

Отличние тумблери к Таранис Лайту

Just used it in project, good finish and solid!!

Just used it in project, good finish and solid!!

Just used it in project, good finish and solid!!

I was looking for very small switches to repair some slim LED lights with damaged switches. They are the only ones that fit on it. I was skeptical when I received them but they work fine, really. Not tried on 220V or 6A because I'm not sure they are made for. Be careful with the soldering iron not to overheat the switches and if you burn one : don't cry, the price is so low ! Je recherchais de tout petits inters pour remplacer sur des réglettes a LED très fines et c'est les seuls à pouvoir se loger sur la tranche. J'étais dubitatif en les voyant mais ils fonctonnent correctement. Pas d'essai sur le 220V ou 6A car ils ne paraissent pas taillés pour Attention à ne pas trop chauffer en soudant car le plastique pourrait s'abimer et si c'est le cas pas de soucis vu le prix.

I was looking for very small switches to repair some slim LED lights with damaged switches. They are the only ones that fit on it. I was skeptical when I received them but they work fine, really. Not tried on 220V or 6A because I'm not sure they are made for. Be careful with the soldering iron not to overheat the switches and if you burn one : don't cry, the price is so low ! Je recherchais de tout petits inters pour remplacer sur des réglettes a LED très fines et c'est les seuls à pouvoir se loger sur la tranche. J'étais dubitatif en les voyant mais ils fonctonnent correctement. Pas d'essai sur le 220V ou 6A car ils ne paraissent pas taillés pour Attention à ne pas trop chauffer en soudant car le plastique pourrait s'abimer et si c'est le cas pas de soucis vu le prix.

I was looking for very small switches to repair some slim LED lights with damaged switches. They are the only ones that fit on it. I was skeptical when I received them but they work fine, really. Not tried on 220V or 6A because I'm not sure they are made for. Be careful with the soldering iron not to overheat the switches and if you burn one : don't cry, the price is so low ! Je recherchais de tout petits inters pour remplacer sur des réglettes a LED très fines et c'est les seuls à pouvoir se loger sur la tranche. J'étais dubitatif en les voyant mais ils fonctonnent correctement. Pas d'essai sur le 220V ou 6A car ils ne paraissent pas taillés pour Attention à ne pas trop chauffer en soudant car le plastique pourrait s'abimer et si c'est le cas pas de soucis vu le prix.

This is a SPDT switch. The thread is 4.85mm. handle is 11mm. Nice feel to action

This is a SPDT switch. The thread is 4.85mm. handle is 11mm. Nice feel to action

This is a SPDT switch. The thread is 4.85mm. handle is 11mm. Nice feel to action

المنتج الجيد، بائع سريع، أنا كُنْتُ مسرورَ بالشراءِ

Produto bom, vendedor rápido, fiquei satisfeito com a compra

المنتج الجيد، بائع سريع، أنا كُنْتُ مسرورَ بالشراءِ

يبدو جيداً. بعض المشاكل البسيطة في تركيب الجوز

Looks fine. Some minor fitting problems with nut-screew

يبدو جيداً. بعض المشاكل البسيطة في تركيب الجوز

منتج جيد

Good Product

منتج جيد