استعراضات العملاء

أكتب مراجعة
  • كل المراجعات (6)
  • صورة (3)
  • فيديو (0)
  • بداية الكل
    • بداية الكل(6)
    • 5 بدأ(6)
    • 4 بدأ(0)
    • 3 بدأ(0)
    • 2 بدأ(0)
    • 1 بدأ(0)
الترتيب حسب:
أفضل مراجعة
  • أفضل مراجعة
  • الأكثر أفاده
  • آخر
المراجعات من بلدك فقط (Iraq)
|
إظهار النسخة الأصلية

تمت ترجمة جزء من المراجعة تلقائيًا.

  • 21/05/2019

    As far as upgrades are concerned, I cannot see any difference between the original and this one. That aside, this is a cheap way to get into 32bit boards while using the still ubiquitous RAMPS. The board is of high quality. However this board(including the original from Panucatt) has a few shortcomings compared to the mega. 1. Few less pins than mega 2. SPI mode with TMC2208 drivers 3. Using the RepRap Discount Graphics LCD There's a hack to get the LCD working, by getting 5V from some other pin. I'd say this is not intended for absolute beginners. Smoothieware comes preloaded. With some steps marlin(v2.0) may also be installed. It's easy to upload firmware to this board using the SD card that is included. Despite some hassle, it's a cheap way to really UPGRADE an older printer board!

    تعليقات
    إظهار النسخة الأصلية
  • 21/03/2019

    Easy upgrade if you already have a RAMPS board and you want to switch to 32-bit without making to much changes to your setup. Package arrived nicely packaged, includes a USB mini cable and MicroSD-card. On said MicroSD you get Smoothieware preloaded but you could also run Marlin 32-bit instead (Marlin has a special version for this board ) Quality is ok, not perfect soldering but well above what I expected! Might order more to keep as spares

    تعليقات
    إظهار النسخة الأصلية
  • 19/06/2019

    works perfectly fine , also came with a 128 MB sdcard to hold the operating system and eeprom files

    تعليقات
    إظهار النسخة الأصلية
  • 28/10/2019

    Alles OK.

    تعليقات
    إظهار النسخة الأصلية
  • 24/06/2019

    Product as described. I do recommend.

    تعليقات
    إظهار النسخة الأصلية
  • 09/05/2019

    Precisely what I ordered. Already working in my printer, straight swap with Arduino, just logic levels with inductive sensor was a bit of a problem.

    تعليقات
    إظهار النسخة الأصلية
Show:

    مجموع 0 الصفحات

    انتقل إلى صفحة

    recommendation for you
    • US$299.00
    • US$399.00
    • US$299.00
    • US$399.00
    • US$999.00
    • US$989.00
    • US$599.00
    • US$299.00
    • US$34.99
    • US$999.00
    • US$499.00
    • US$419.00
    • US$299.00
    • US$499.00
    • US$339.00
    • US$63.99
    • US$64.99
    • US$14.99