استعراضات العملاء

أكتب مراجعة
  • كل المراجعات (264)
  • صورة (25)
  • فيديو (0)
  • بداية الكل
    • بداية الكل(264)
    • 5 بدأ(240)
    • 4 بدأ(21)
    • 3 بدأ(3)
    • 2 بدأ(0)
    • 1 بدأ(0)
الترتيب حسب:
أفضل مراجعة
  • أفضل مراجعة
  • الأكثر أفاده
  • آخر
المراجعات من بلدك فقط (Iraq)
|
إظهار النسخة الأصلية

تمت ترجمة جزء من المراجعة تلقائيًا.

  • 15/08/2019

    Nice and cheep Product. The LDO is a LM6206, so the max input voltage is 6.5V. The board is based on a TLC555 and outputs a voltage from 3.3V to 0V. It consumes around 4mA at 5V or 3.3V. Wet soil gives a lower voltage than dry soil.

    تعليقات (1)
    إظهار النسخة الأصلية
  • 18/07/2018

    The sensor is based on an a-stable multi vibrator circuit using a 555 where the output duty cycle changes with the sensed capacitance. The simply over an RC circuit integrated signal is the board's output. Unfortunately, the discharge time constant on C (1µF) on this model (Ver. 1.2) seems very high (>10 sec) which is caused by too high valued or non existing discharge resistor. So I simply added a 1.2M resistor from the board's output to ground. There is just enough room at the connector side and already existing via's to easily solder a small 1/10W radial resistor on. This may slightly limit the output swing but gives more stable result voltages.

    تعليقات
    إظهار النسخة الأصلية
  • 09/10/2018

    not yet tested, product as per website description. some fluxant residue on the solder joints. it looks Ok, satisfied non ancora testato, prodotto come da descrizione del sito web. alcuni residui flussanti sui giunti di saldatura. sembra Ok, soddisfatto

    تعليقات
    إظهار النسخة الأصلية
  • 02/10/2020

    منتج ممتاز ومكتمل بشكل جيد جداً.

    تعليقات
    إظهار النسخة الأصلية
  • 25/09/2019

    good price, good quality

    تعليقات
    إظهار النسخة الأصلية
  • 02/09/2019

    Seems good.

    تعليقات
    إظهار النسخة الأصلية
  • 03/07/2019

    These are definitely an upgrade to the older fork sensors, and seem to be coated quite well with some sort of epoxy compound to reduce corrosion. The edges of the board, however, are still raw PCB and I would recommend touching them up with some 2 part epoxy before calibration and use, just to extend the life of the part.

    تعليقات
    إظهار النسخة الأصلية
  • 23/11/2018

    tested Vcc = 3,3V Wide Voltage 2.5 V 0,68 V

    تعليقات
    إظهار النسخة الأصلية
  • 25/04/2021

    ممتاز ولكن حذر يعمل بمعدل 4.5 فولت على الأقل وليس 3.3 فولت. لأنه يقوم بتركيب N555 المتكامل الذي يتطلب 4.5 فولت على الأقل

    تعليقات
    إظهار النسخة الأصلية
  • 16/07/2019

    Works fine. I use it with an ESP8266. Be careful: ESP8266 analog input's max. voltage is 1 V! The sensor's max. output voltage is at about 2.8 V.

    تعليقات
    إظهار النسخة الأصلية
Show:

    مجموع 0 الصفحات

    انتقل إلى صفحة

    قد تكون مهتمة ايضا بـ

    recommendation for you
    • US$4.99
    • US$16.00
    • US$9.99
    • US$10.99
    • US$13.99
    • US$1.61
    • US$9.99
    • US$15.99
    • US$7.99
    • US$14.99
    • US$23.99
    • US$8.99
    • US$8.99
    • US$6.69
    • US$9.99
    • US$13.99
    • US$7.99
    • US$18.99