استعراضات العملاء

أكتب مراجعة
  • كل المراجعات (111)
  • صورة (11)
  • فيديو (1)
  • بداية الكل
    • بداية الكل(111)
    • 5 بدأ(105)
    • 4 بدأ(4)
    • 3 بدأ(1)
    • 2 بدأ(0)
    • 1 بدأ(1)
الترتيب حسب:
أفضل مراجعة
  • أفضل مراجعة
  • الأكثر أفاده
  • آخر
المراجعات من بلدك فقط (Iraq)
|
إظهار النسخة الأصلية

تمت ترجمة جزء من المراجعة تلقائيًا.

  • 01/04/2016

    This is a 44E hall sensor. Simple to connect and use with Arduino/Genuino projects. The 3 connectors are GND (-), VCC 5v (in the middle without label) and signal. From testing this sensor it seems to be quite digital, so reading nearly high value when no magnetic field is close to the sensor, dropping to low (ground) when magnet is coming close to sensor (distance 10-12mm). Please note the sensor will only react to north of the magnet, so make sure to use it in the right direction. When magnetic field is strong enough, a small LED will light green and signal drop to low.

    تعليقات
    إظهار النسخة الأصلية
  • 02/09/2013

    Pros: Quite easy to figure out without any documentation, all the pins are either well-labeled or obvious. Good quality for the price.Also it is really small so it could be hidden if you wanted to. Cons: None that I can think of... Work right away and compatible with arduino, mbed and all kind of other mircocontroller boards. I don't have any cons till now and I can not think of any. Especially for this price!!! Other: Easy to interface to my Arduino, good deal. I will recommend this to friends.

    تعليقات
    إظهار النسخة الأصلية
  • 04/07/2016

    Bon produit. Livraison rapide.

    تعليقات
    إظهار النسخة الأصلية
  • 30/01/2019

    beau petit module, pas encore testé car magnétisme pas encore livrés

    تعليقات
    إظهار النسخة الأصلية
  • 29/12/2018

    Teşekkür ederim kullanacağım - 謝謝你我會用 - Thank you I will use

    تعليقات
    إظهار النسخة الأصلية
  • 26/08/2014

    I bought 3 of them to make probe for my 3d printer Their accuracy is correct and the repeatability is great ==> my first layer is always of 0.25mm. Just need a little bit of kapton or other tape to isolate the pads beneath the pins of the sensor

    تعليقات
    إظهار النسخة الأصلية
  • 19/09/2020

    إستلمت بشكل جيد وبترتيب جيد ما زالَ يَحتاجُ للإختبار أولاً.

    تعليقات
    إظهار النسخة الأصلية
  • 08/09/2020

    عظيم، لا أستطيع الانتظار لتجربة هذه

    تعليقات
    إظهار النسخة الأصلية
  • 13/03/2019

    parfait 👌

    تعليقات
    إظهار النسخة الأصلية
  • 25/03/2018

    Tested with 5v and it's working great. The sensor doesn't stand above the board as shown in the listing picture. I'm not sure if that'll matter to me or not.

    تعليقات
    إظهار النسخة الأصلية
Show:

    مجموع 0 الصفحات

    انتقل إلى صفحة

    قد تكون مهتمة ايضا بـ

    recommendation for you
    • US$12.49
    • US$8.99
    • US$12.43
    • US$6.69
    • US$13.81
    • US$11.99
    • US$14.49
    • US$11.99
    • US$19.99
    • US$4.99
    • US$8.99
    • US$4.99
    • US$3.99
    • US$8.49
    • US$8.99
    • US$7.99
    • US$9.28
    • US$11.23