wacekdz
محتوياتي
كل الرسائل
استعراضات
تعليقات
أجابات
الأسئلة

كل الرسائل

wacekdz 04/05/2019
It's a very nicely build copter. The motors have quite a lot of power and the Caddx Camera V2, though snugly fit, still does its job perfectly. It flies really well on 3S, which is great. It's still not perfect for freestyle, but the capabilities for the price are really great. There is a 'but' however. The ESCs are rated only for 5A on the Crazybee F4 V2.0 board, which the copter gets shipped with. Banggood started warning customers about lowering the throttle curve to ~75%, but that's just unjustified to sell the product knowing that it might burn out. Mine did. After falling into some debris, the motors spun just for a quick moment, enough to burn the F4 board (ESC + receiver chip - dunno why the latter?). It took along the Caddx Turtle V2 board as it's not powering up when supplying 5V externally (the FC is fried so had to reconnect it somewhere else). Overall BetaFPV at least tried to address the issue, here I don't think there's any support expected. Lowering the throttle curve is surely not the way to go, since any load on the motors will effectively burn the ESCs anyway. It's enough to hit a branch etc. Anyway the approximate repair cost is roughly 50% cost of the whole new copter. Not sue if it's worth at this point, as the ESCs may burn again. Too fragile in my opinion. Last flight of the Mobula 7 HD (its 5th in total): https://youtu.be/GfY7kNZyn1Q
Happymodel Mobula7 HD 2-3S 75 ملم Crazybee F4 Pro V3.0 Flight Controller AIO 10A ESC سينيهووب FPV سباق درون PNP BNF مع محرك 1102 9000KV كاميرا Runcam Splite3 Lite
US$153.99 US$184.99
4
التوصيات
تعليقات (0)
wacekdz 29/11/2018
The faceplate is definetely not made of leather - it's just some soft foam. Used it to exchange the original one in my FS Dominator V3s. It suits the goggles really well, You just have to cut it halfway, at the point where the nose goes, otherwise it won't reach the velcro on the goggle's faceplate. Once that's done, there's little to none light leakage and it's quite comfortable to wear. It's a bit thicker than the original fabric and it's rounded instead of being flat. Overall satisfied for the price.
2PCS استبدال غطاء جلد الوجه لوحة النسيج كيت ل Fatshark FPV نظارات
US$13.99 US$16.79
0
التوصيات
تعليقات (0)

أنت الخبير ، هل يمكنك المساعدة؟

ندعوك بصدق للاشتراك في البريد الإلكتروني Invite Answer!

إذا قمت بالاشتراك ، فسندعوك عبر البريد الإلكتروني للإجابة على الأسئلة التي يطرحها الأشخاص حول المنتجات. باشتراكك] سوف تكسب أيضًا "شارة مفيدة "! يمكنك إلغاء الاشتراك في أي وقت على صفحة إعدادات الخصوصية.

ساعد الآخرين وكن أكثر سعادة!

  • الإشتراك

حول الشارات

ترتبط الشارات بالمجتمع ، ويكسب المستخدمون شارات عن طريق إنشاء محتوى عالي الجودة ، أو إكمال المهام ، أو عن طريق المشاركة في أنشطة خاصة. وسيكون للأشخاص المعنيين أيضًا شارة خاصة بهم.
شارة الرئيس التنفيذي

شارة المدير التنفيذي مملوكة فقط من قبل رئيس شركة بانجوود.

شارات يمكنك كسب قريبا
  • حسنا

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • حسنا

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe