كل الرسائل

سؤال: Is this tinned pure copper or is it CCA wire?

السؤال بواسطة BG225733103 على 2022-10-04 12:13:40

Burplerlcbm tinned copper

2022-10-05 08:22:57 مساعدة (0)
عرض
أجابات (1)

سؤال: What is RTC for each tip?

السؤال بواسطة BG143912477 على 2022-03-19 01:31:58

BG225733103 RTC? Wich definition of RTC are you talking about? Your Question makes no sense...There are lots of different meanings for RTC. See here: en.wikipedia.org | wiki | RTC If you want people to help you stop using acronyms and give more context instead of just a short question.

2022-03-19 04:06:24 مساعدة (0)
عرض
أجابات (2)

سؤال: good morning, what kind of blade does it take? is it surgical blade and what number? thank you

السؤال بواسطة sotos123 على 2020-11-20 12:17:35

BG225733103 Sure looks like a scalpell blade to me. The blade shown here seems to be for use with a scalpell handle no 3 or 4. Blade shape could be a Rüttgers no 11 or an Aesculap no 25. But the mounting slot is the same for all blade shapes, so you can use any shape you like. Use your favorite image search engine to search for "scalpell blade shapes" to find the one you want.

2021-09-16 03:45:51 مساعدة (1)
عرض
أجابات (2)

سؤال: What kinds of probes/leads should I use?

السؤال بواسطة cubeconvict على 2019-06-27 10:47:07

BG225733103 Bare wire is probably best. I suspect that it was never intended for banana plugs, but as pure screw terminals. Hole diameter in the plastic head is about 5.5mm.

2021-08-29 01:06:26 مساعدة (0)
عرض
أجابات (6)

سؤال: what kind of fuses use? 5x20 mm? and how much amperes are each one?

السؤال بواسطة pjlabarta على 2019-09-29 08:59:13

BG225733103 I suspect that the fuses that are currently present will be installed with respect to the current. My board contained 5A fuses.

2021-08-29 12:57:48 مساعدة (0)
عرض
أجابات (6)

سؤال: Can I get 24V by connection with 12V and -12V?

السؤال بواسطة BG405471057 على 2021-08-22 02:03:19

BG225733103 On the board is no circuitry that would prevent you from using the +12V with the -12V instead of GND - the screw terminals are connected straight to the ATX connector via a fuse only. So yes, you __could__ get a 24V potential. If it works or if it goes bang depends entirely on the ATX PSU that you connect to the board.

2021-08-29 12:50:15 مساعدة (0)
عرض
أجابات (8)

سؤال: Are their 220 Ohm and 10 k values resistors?

السؤال بواسطة BG019391538 على 2021-08-03 04:09:34

BG225733103 all Ω values are listed in the overview.

2021-08-03 10:36:45 مساعدة (1)
عرض
أجابات (9)

سؤال: do you have 1k resistors included

السؤال بواسطة BG153723470 على 2020-11-06 07:54:55

BG225733103 1kΩ is listed in the value list shown in the overview, so yes there are 20 pieces.

2021-08-03 10:33:15 مساعدة (0)
عرض
أجابات (2)

سؤال: How much current does it draw?

السؤال بواسطة BG225733103 على 2021-06-22 07:09:26

Joao 12v

2021-07-14 09:58:55 مساعدة (0)
عرض
أجابات (1)

سؤال: what is the diameter of the schankjQuery1113003623391781673546_1621751611324

السؤال بواسطة Shaya على 2021-05-23 01:39:13

BG225733103 Inthe description it says 3mm. Measured with a caliper the shanks are between 3,09mm and 3.16mm

2021-05-25 06:21:04 مساعدة (0)
عرض
أجابات (2)

سؤال: When I plugged in the 24-pin ATX PSU, no voltages were shown on the PCB terminals. What is missing?

السؤال بواسطة hcemc على 2019-12-27 02:06:53

BG225733103 Isthe LED indicating power on? If yes, make sure the 5A fuses aren't blown.

2021-05-25 06:16:21 مساعدة (0)
عرض
أجابات (8)