Works well, very compact adapter. I put up a picture showing how you can modify the board to work with Arduino. Just cut the trace going from the chip to the R3 resistor, then solder a tiny wire from the chips' top left pin (pin 28) to the RST pin.

Works well, very compact adapter. I put up a picture showing how you can modify the board to work with Arduino. Just cut the trace going from the chip to the R3 resistor, then solder a tiny wire from the chips' top left pin (pin 28) to the RST pin.

Works well, very compact adapter. I put up a picture showing how you can modify the board to work with Arduino. Just cut the trace going from the chip to the R3 resistor, then solder a tiny wire from the chips' top left pin (pin 28) to the RST pin.

Drivers available: http://www.silabs.com/products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx I didn't need to install driver for openSUSE 12.3 (3.7.10 kernel). As usual, a tiny bit of documentation would be comforting. Using the supplied jumper between RXC and TXC, loopback works. Remove jumper. Connect GND (blk) to GND, RXC (wht) to RXD, TXC (gry) to TXD, 5V (vio) to VCC. (RST (blu) to RESET?)

Drivers available: http://www.silabs.com/products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx I didn't need to install driver for openSUSE 12.3 (3.7.10 kernel). As usual, a tiny bit of documentation would be comforting. Using the supplied jumper between RXC and TXC, loopback works. Remove jumper. Connect GND (blk) to GND, RXC (wht) to RXD, TXC (gry) to TXD, 5V (vio) to VCC. (RST (blu) to RESET?)

Drivers available: http://www.silabs.com/products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx I didn't need to install driver for openSUSE 12.3 (3.7.10 kernel). As usual, a tiny bit of documentation would be comforting. Using the supplied jumper between RXC and TXC, loopback works. Remove jumper. Connect GND (blk) to GND, RXC (wht) to RXD, TXC (gry) to TXD, 5V (vio) to VCC. (RST (blu) to RESET?)

Получил устройство за 21 день. Драйвер автоматически установился быстро на Win/ 7 (64). Все работает. я доволен. Рекомендую.

Получил устройство за 21 день. Драйвер автоматически установился быстро на Win/ 7 (64). Все работает. я доволен. Рекомендую.

Получил устройство за 21 день. Драйвер автоматически установился быстро на Win/ 7 (64). Все работает. я доволен. Рекомендую.

There isn't DTR contact. Because of this you can not flash micro minimOSD (I think other osd plates too)

There isn't DTR contact. Because of this you can not flash micro minimOSD (I think other osd plates too)

There isn't DTR contact. Because of this you can not flash micro minimOSD (I think other osd plates too)

мне понравилось, визуально... Когда заказывал было дикое желание и необходимость, а сейчас даже не помню что хотел. :) Вот так это выглядит)

мне понравилось, визуально... Когда заказывал было дикое желание и необходимость, а сейчас даже не помню что хотел. :) Вот так это выглядит)

мне понравилось, визуально... Когда заказывал было дикое желание и необходимость, а сейчас даже не помню что хотел. :) Вот так это выглядит)

need this absolutely but still waiting for since November 2016, resent by BG in March

need this absolutely but still waiting for since November 2016, resent by BG in March

need this absolutely but still waiting for since November 2016, resent by BG in March

الطرد تم تسليمه بسرعة و وصل في غضون شهر يبدو أنها تعمل، ولكن سوف تحقق من ذلك.

The parcel was delivered quickly, it arrived within a month. Looks like it works, but I'll check it out.

الطرد تم تسليمه بسرعة و وصل في غضون شهر يبدو أنها تعمل، ولكن سوف تحقق من ذلك.

لقد نجحت!

ça fonctionne !

لقد نجحت!

Buon convertitore USB TTL, realizzato discretamente ed isolato con guaina termorestringente trasparente. Ha tre LED sul pcb che conferma la sua alimentazione e di funzionamento. La scocca del connettore USB non è ben saldato al pcb, si consiglia di saldarlo al pcb per evitare rotture in fase di inserimento o estrazione da/verso porta USB, comunque io ho ripassato tutte le saldature del connettore USB. Compresi 4 cavetti da 12 cm per il collegamento. Consigliato per programmazione ESP8266.

Buon convertitore USB TTL, realizzato discretamente ed isolato con guaina termorestringente trasparente. Ha tre LED sul pcb che conferma la sua alimentazione e di funzionamento. La scocca del connettore USB non è ben saldato al pcb, si consiglia di saldarlo al pcb per evitare rotture in fase di inserimento o estrazione da/verso porta USB, comunque io ho ripassato tutte le saldature del connettore USB. Compresi 4 cavetti da 12 cm per il collegamento. Consigliato per programmazione ESP8266.

Buon convertitore USB TTL, realizzato discretamente ed isolato con guaina termorestringente trasparente. Ha tre LED sul pcb che conferma la sua alimentazione e di funzionamento. La scocca del connettore USB non è ben saldato al pcb, si consiglia di saldarlo al pcb per evitare rotture in fase di inserimento o estrazione da/verso porta USB, comunque io ho ripassato tutte le saldature del connettore USB. Compresi 4 cavetti da 12 cm per il collegamento. Consigliato per programmazione ESP8266.

المنتج وصل بصوره جيده ومغلف بطريقه جيده وصل خلال ٢١ يوم وهو وقت مناسب جدا

المنتج وصل بصوره جيده ومغلف بطريقه جيده وصل خلال ٢١ يوم وهو وقت مناسب جدا

المنتج وصل بصوره جيده ومغلف بطريقه جيده وصل خلال ٢١ يوم وهو وقت مناسب جدا