استعراضات العملاء

4.65 من 5
أكتب مراجعة
  • كل المراجعات (17)
  • صورة (5)
  • فيديو (0)
  • بداية الكل
    • بداية الكل(17)
    • 5 بدأ(11)
    • 4 بدأ(6)
    • 3 بدأ(0)
    • 2 بدأ(0)
    • 1 بدأ(0)
الترتيب حسب:
أفضل مراجعة
  • أفضل مراجعة
  • الأكثر أفاده
  • آخر
  • zeroku
    ES
    2020-10-26 02:34:08

    maravillosa, una estructura indestructible, clon bmg.... guías lineales lo mejor increíble por este precio. lo peor es fusor pero por 20€ pones un v6 clon bueno

    تعليقات
  • 2020-10-10 12:45:07

    Wurde schnell geliefert und war nach 2h aufgebaut, nur mit der Firmware war ich nicht zufrieden, da sie nicht funktioniert hat. Mit ganz neue Software läuft der Drucker super. Drückt schnell und leise.

    تعليقات (1)
  • msq7131
    US
    2020-06-13 06:57:22

    nice printer. good shipping time

    تعليقات
  • 2020-07-25 17:20:39

    Quality is strong and precise, but some design mistakes and quality is not good for the extruder and hot end, the grip of the extruder is a crap and lot of clogging appended, but for the price... And the possibility to upgrade with another head is great.

    تعليقات
  • 2020-07-19 12:20:04

    parasına göre güzel

    تعليقات
  • 2020-07-23 16:25:19

    printer arrived , well packaged, minor dents from factory, pulleys reversed, and minimal instructions the video and the manual are almost laughable in their simplicity and could be vastly more informative. The config or whatever file tells it where or how to home is incorrect and the bed will continue to drop until you have to shut it off to stop the motors as there is no end stop on the bottom, while the x and y bunch up in the left rear corner, it looks good and sturdy I would love to try it but

    تعليقات (2)
  • 2020-07-15 05:01:58

    couple of issue that i hope to get resolved with the manufacturer. who by the way dose not seem to answer any questions at all. so dont count on getting support from them. the printer itself of of good build as far as the structure goes. but will need upgrading of the printhead bad design, liner rails 2 Z asxis are not straight,all pullys are plastic and the belts feel like they will streatch. the build instructions are a compleet waste of your time. but any compitent person can quicky work it

    تعليقات (1)
  • 2020-10-26 08:16:50

    The construction is very strong and solid. Everything fits well. They have fixed all the critics and errors reported by previous reviewers. Yet, on mine, the screw & nut for fixing the filament sensor were missing. The instruction manual is too small and missing many subject like how to install the belt and how to tension them correctly.

    تعليقات (1)
  • ytdytd
    DE
    2020-06-26 03:32:20

    Received this printer very fast. The printer needs some adjustments as the belt system is not properly aligned. I had to reduce the height of the pulley stands on the upper frame to achieve proper alignment. The fan of the power supply is very noisy and has to be changed. The motor cables to the x stepper motor were 20cm too short. I had to solder on new wires. The end-switch for the Z axis had to be installed upside down compared to the instruction manual. The aluminium printbed is warped and the

    تعليقات
  • 2020-05-20 10:42:39

    Pretty good printer. Very solid, absolutely no wobbling. Easy to assemble. Just couple of issues: 1) it arrived without fan on hot-end's heat sink 2) Z-axis rods was 2 cm longer than needed and head crushed into left rod during homing.

    تعليقات (1)
Show:

    Go to page

    Go

    قد تكون مهتمة ايضا بـ

    recommendation for you
    • US$319.99
    • US$529.00
    • US$399.00
    • US$399.99
    • US$319.00
    • US$179.99
    • US$206.00
    • US$399.00
    • US$219.99
    • US$279.00
    • US$259.00
    • US$24.99
    • US$12.99
    • US$12.28
    • US$7.80
    • US$21.48
    • US$3.70
    • US$549.00