LILYGO® TTGO ESP32 WiFi + bluetooth 18650 البطارية لوحة حماية 0.96 بوصة OLED أداة تطوير
تمت ترجمة جزء من المراجعة تلقائيًا.
المنتج كوصف. اختبار جيد يعمل كما هو متوقع. لقد أصبت بصدمة عاطفية عندما لاحظت تشوه واضح في الغطاء المعدني للوحدة بسبب شيء حاد فوقه لحسن الحظ لم يتم كسر شاشة الوحدة القديمة. وفي الآونة الأخيرة، كانت طلبات كثيرة من هذا البائع غير معبأة من حيث الحماية أثناء العبور. فقط حقيبة مضادة للكهرباء داخل ظرف ورقي و داخل ظرف بلاستيكي أكبر لا توجد رقاقة فقاعات لحماية العناصر الهشة داخلها على سبيل المثال. Icd Oold، وهذه يمكن أن تتلف بسهولة من خلال المناولة الخام أثناء النقل. ويمكن أن يوفر هذا الإجراء في الأجل القصير مالا للبائع ولكنه فخ لأن الزبائن سيبدأون في الأجل الطويل في تجنب الشراء من هذا البائع بسبب ارتفاع معدل الوفيات عند وصول المنتجات. لوحة جيدة أوصي.
it has a revision 1 chip it only has space for unprotected 18650 batteries
After a long search I finally had all the information to create my own sketches. So far, everything works. The OLED display is glued to the board. The adhesive dissolves after a short time. Doesn't look good, but it's harmless. Also a warning to everyone: The USB plug is soldered without through-plating and detaches relatively easily from the board. I am not the first to whom this happens. With my first board it happened already with the third plugging in. It's a case for e-waste. The connector goes very tight and is barely able to cope with the forces. This is now my second board and I will take appropriate precautions to prevent this from happening again.
The unit is tidy, but perhaps a little larger than I was expecting, the measurements on pictures are accurate though. I took note of previous comments and have applied a couple of drops of superglue to the USB connector to stop it snapping off. I have used a 4x18650 battery pack which should allow this to run for ages, so far I have only run the demo The OLED display looks white, but shows up blue in the photograph. Be aware that the standard 0,1" DuPont style headers supplied with the unit will NOT connect to a breadboard if soldered to the underside because of the depth of the battery holder - you would to use female to male extenders - you could always solder them to the top, but you wouldn't see the OLED I intend to use this without the headers, so it doesn't make any difference to me
board is working and looking great
Good product. Recommended.
حصلت على وحدتي لساعة الدايود شاشة PV. هذه الوحدة تتضمن الواي فاي لذا قام بتحديث الساعة من الإنترنت و لا أحتاج أبداً لإجراء تعديلات بين الصيف و الشتاء ولست بحاجة إلى تصحيح الوقت. هو مكان للبطارية على الوحدة.
ليس منتجاً ليلياً رسمياً ولكنه يستند إلى التخطيط الرسمي (ليس لديه شعار ttgo). إنه يعمل مثل السحر ذُو. هذا هو النموذج القديم. النموذج الجديد يسمى Lilygo tgo t18. أمثلة برنامج & موجودة على GitHub وعلى بحث جوجل البسيط. (استخدم الكلمات الرئيسية التالية: ttgo خام وحامل البطارية). يوصى بشدة لأنه يتم شحنه من المملكة المتحدة. تأكد من أن وزن البطارية يجعلها عرضة للسقوط واضغط على موصل USB في حالة توصيل الكابل
la confezione non ha molte protezioni, ma non avendo i pin montati l'articolo non presenta danni. arriva con preinstallato uno scatck per il test del display. ho testato anche la batteria e funziona.
Very good ESP32 board. The built in OLED display is very easy to read. Bright enought. The Battery charger working fine. Recommended to buy together with a good 18650 battery.