تمت ترجمة جزء من المراجعة تلقائيًا.
I used this module to build a variable power supply. I use an input voltage of 12 volts (from a computer power supply) and need this module to create a variable (settable via the potmeter) output voltage ca 1 - 30 volt. With output voltages over 12 volts everything works fine. In the step down mode (voltages below 12 volt) the output voltage is not stable. For instance if I set the output voltage to 5 volts and apply no or very little load, then the outputvoltage "swings" between 4.8 and 5.3 volt. This only stops if I apply a larger load that draws at least 500mA of current.
منتج رائع، استخدمته لبناء مصدر طاقة مقعدي بقناتين متغيرتين.
الطلب في الوقت المحدد ومعبأة جيداً اختبرته بمصدري المكتبي ووضعت عدّة عدادات على المخرج ووضعته لمخرج منخفض التوتر لم يسخن ولكني أوصي بأقصى قدر من الحرص على عدم عكس اتجاه توترات الدخول لأنها قد تثير المشاكل. صغيرة جداً وصغيرة جداً أوصي بهذه المادة. انظر إلى الصور وما شابه.
جيد جداً، سفينة مع حقيبة مضادة للكهرباء تم تعبئة المنتج بشكل صحيح. تنظيم الخط جيد، تم اختباره مع إدخال 5-30 فولت، وحمل 2 أمبير. مناسب للضوء، أو لا يوجد جهاز تناظري بدون عامل تصفية. القيود الحالية تعمل بشكل جيد لقد خاب أملي قليلاً في اختيار المكثف إنها درجة حرارة 105، لكن فقط 35 فولت، 50 فولت كانت لتسمح بحياة أفضل.
This is excellent step-up/step-down converter, that can be used for simple bench power supply. Replace variable resistors with these panel mounting 250 KOhm potentiometers ( http://bit.ly/2wOHvro ), add solid power supply ( http://bit.ly/2wOrJfY ) voltage/current monitor ( http://bit.ly/2wOrWjg ) and put everything in a nice box ( http://bit.ly/2wOHVOu )
this converter can help you in solving many power supply problems. it is able to increase or decrese the voltage at its output terminal compared to the input voltage. the output is quite stable with the load change and the multi turns trims help you in adjusting the output voltage level and the max output current as per your needs. One of the thermal pad below the MOSFET was slightly out of position, but I solved this issue very quickly - check the pads before power up the circuit. good value for money. suggested questo convertiore permette di aumentare o diminuire la tensione in uscita rispetto al valore della tensione di ingresso. la tensione di uscita è stabile rispetto alle variazioni della corrente del carico. i trim multigiri permettono una buona regolazione della tensione e della massima corrente di uscita. Un MOSFET aveva il pad termico leggermente fuori posto, ma ho risolto velocemente il problema. suggerisco un controllo dei pad termici prima di dare tensione al circuito ottimo valore per il prezzo. suggerito
Seems to work well. I will use it to have a portable power pack for all situations (recharge PC, drone Lipos, etc.). Will see how it hold up in time.
Преобразователь из низкого напряжения от 1.5 вольт может заряжать аккумулятор 12-24 вольта,правда при этом достаточно сильно греется.
I am using this to boost battery voltage to supply power into a class D amplifier. Now I can use full volume without clipping.
Works great and it doesnt heat up. Used a 12V SMPS with this and can only reach 1.1V - 29V. I hoped to reach 30V but this has the best value for buck boost converters here. 5 stars!