استعراضات العملاء

أكتب مراجعة
  • كل المراجعات (7508)
  • صورة (930)
  • فيديو (12)
  • بداية الكل
    • بداية الكل(7508)
    • 5 بدأ(7265)
    • 4 بدأ(185)
    • 3 بدأ(22)
    • 2 بدأ(14)
    • 1 بدأ(22)
الترتيب حسب:
أفضل مراجعة
  • أفضل مراجعة
  • الأكثر أفاده
  • آخر
المراجعات من بلدك فقط (Iraq)
|
إظهار النسخة الأصلية

تمت ترجمة جزء من المراجعة تلقائيًا.

  • 27/08/2014

    The cheapest way to get the Nano v.3. USB cable is the standard one. I had problems recognizing in W7-x64 but it works perfect after installing new driver (different of Ardudino Uno), Can download from http://robotstore.cz/obchod/arduino/dccduino-nano-v3-0-atmega328-ch340g-arduino-rozsirujici-deska/

    تعليقات (1)
    إظهار النسخة الأصلية
  • 02/08/2019

    Works great. Used in project to run a OLED screen. You need to install CH340 drivers and select "old bootloader" in Arduino IDE in order for it to conect. Price unbeatable.

    تعليقات (1)
    إظهار النسخة الأصلية
  • 12/02/2020

    منتج رائع Great product تجربه رائعه great experience ملحوطه هذا المنتج يعمل بالبوت لودر القديم This product works using (old Bootloader)

    تعليقات
    إظهار النسخة الأصلية
  • 26/02/2018

    This is really nice board. Silkscreen is readable. Only complaint I have is that board has mini usb instead of micro usb connector, so you might need to get cable for it: http://bit.ly/2oj7ZeB You will have to solder pins yourself, if you’re not into it, there is board with pins already soldered: http://bit.ly/2oeN5gH

    تعليقات
    إظهار النسخة الأصلية
  • 03/12/2017

    This is quite nice board. Silkscreen is nice and readable. Only complaint I have is that board has mini usb instead of micro usb connector, so you might need to get mini usb cable: https://goo.gl/MgE41a You will have to solder pins yourself, if you’re not into it, there is board with pins already soldered: https://goo.gl/PYEipY

    تعليقات
    إظهار النسخة الأصلية
  • 23/11/2014

    Incredible price for this small device. But with the normal ftdi-drivers this nano wasn't recognized and installed properly (Win 7 64bit). With the following drivers the problems were fixed. Now the clone runs absolutely flawless like an original one. Drivers: http://www.winchiphead.com/download/CH341/CH341SER.ZIP

    تعليقات
    إظهار النسخة الأصلية
  • 01/10/2018

    Nice little controller for HAM radio fox-hunting transmitter on 80-meters. Have built the transmitter board and the Arduino Nano is piggy backed upon it. Arduino takes care of the timing (transmitter on and off) and generates the Morse code to be transmitted. Five of these units are operational at this time, more to follow!

    تعليقات
    إظهار النسخة الأصلية
  • 25/01/2021

    كما هو الحال بالفعل، كل الأدوينو تعمل في حالة ممتازة. وهي مبرمجة بالفعل وجاهزة للاستخدام. يُرجى ملاحظة الكابل المطلوب استخدامه، فهناك كابلات لا تعمل بشكل جيد، وهي ليست من الأاردوينو. استخدم "نانو" "محمّل تمهيد قديم"

    تعليقات
    إظهار النسخة الأصلية
  • 07/08/2017

    This is quite nice board. I tested it on my mac, and it worked like a charm. Silkscreen is more readable than on some other nano boards I have. Only complaint I have is that board has mini usb instead of micro usb connector, which is far less common, so you might need to get mini usb cable: https://goo.gl/MgE41a. You will have to solder pins yourself, if you’re not into it, there is board with pins pre soldered: https://goo.gl/PYEipY

    تعليقات
    إظهار النسخة الأصلية
  • 20/10/2019

    Operational only with old bootloader (in Arduino IDE)!

    تعليقات (1)
    إظهار النسخة الأصلية
Show:

    مجموع 0 الصفحات

    انتقل إلى صفحة

    قد تكون مهتمة ايضا بـ

    recommendation for you
    • US$5.99
    • US$38.99
    • US$13.99
    • US$14.99
    • US$32.03
    • US$9.99
    • US$14.99
    • US$18.85
    • US$9.99
    • US$42.52
    • US$353.99
    • US$13.99
    • US$39.99
    • US$52.38
    • US$115.99
    • US$18.99
    • US$59.19
    • US$26.99