استعراضات العملاء

4.7 من 5
أكتب مراجعة
  • كل المراجعات (175)
  • صورة (19)
  • فيديو (0)
  • بداية الكل
    • بداية الكل(175)
    • 5 بدأ(146)
    • 4 بدأ(16)
    • 3 بدأ(7)
    • 2 بدأ(2)
    • 1 بدأ(4)
الترتيب حسب:
أفضل مراجعة
  • أفضل مراجعة
  • الأكثر أفاده
  • آخر
  • gus
    GI
    2019-10-11 15:34:18

    Item received on time and as specified in description. Fun and easy to assemble and works well.

    تعليقات
  • Steve
    AU
    2019-11-10 01:00:44

    I didn't receive a capacitor ?

    تعليقات
  • HandyMn
    CA
    2019-04-15 23:14:02

    Great DIY and easy to assemble ARC lighter. Seems to work fine with surprisingly hi output, capable of producing arc across about 5mm gap (have not tried extreme or it may damage something) Draws about 2.5 A from 5V source, current will increase with smaller arc gap (and so will the frequency of the oscillator). Now I am thinking what case to install it in and rechargeable power source for it...

    تعليقات
  • 2019-02-16 03:30:14

    Simple little soldering project that took just a few minutes to complete - worked first time. The kit is supplied without instructions, and mostly it's possible to figure out where things go. The most confusing item is the actual spark generator (potted coil). There are two insulated wires, and then a number of thinner enamel coated wires. At first glance the enamel coated wires look mixed up, but they are actually soldered at the ends. I placed this unit on the board with the insulated wires

    تعليقات
  • Georgie
    CA
    2019-08-23 14:33:50

    Very nice, works well on a single lithium battery (e.g. 18650 or 1S LiPo). The board has been updated so looks a bit different than the instructions. Transformer connects the same way. There's no more capacitor and Q1 has two pins instead of 3, middle one is cut. You may still need to ensure a connection between the case/middle pin and the pad on the board (B+). There's no more screw to mount Q1 and it heats up during use so thermal paste is highly recommended to transfer heat to the board and keep

    تعليقات
  • Mike
    US
    2019-07-07 14:05:17

    All looks good. I am a novice at soldering and will put together after a little more practice on some of the simpler kits. Although there are not many components on this one there is one that is not a through hole component.

    تعليقات
  • Drzazga
    FR
    2018-10-25 03:28:36

    Produkt zgodny z opisem. Dobrze zapakowany.To kolejny z gadżetów który kupuje dla zabawy ojca z córką. Polecam

    تعليقات
  • 2019-09-05 11:15:31

    easy little kit, did note use tie strap that was supplied for the coil but uv epoxy resin, also parts in description are different but did not affect the build and works.

    تعليقات
  • 2019-07-26 10:16:16

    this is the best diy kit I ever recived. It is very small and when assembled it could fit in your pocket. Its cost is reasonable perfect for diy projects. must buy,but you need to be experienced in soldering and diy projects.

    تعليقات
  • elroy
    GB
    2018-08-12 04:15:30

    The wires on the black transformer are quite fragile so be careful. I made this and it works off of a 1s lipo which is 4.2-3.5V with an arc about 5mm long.

    تعليقات
Show:

    Go to page

    Go

    قد تكون مهتمة ايضا بـ

    recommendation for you
    • US$4.69
    • US$3.99
    • US$3.99
    • US$13.99
    • US$3.99
    • US$5.99
    • US$9.89
    • US$2.99
    • US$3.96
    • US$7.07
    • US$8.50
    • US$16.99
    • US$4.50
    • US$3.99
    • US$36.99
    • US$8.19
    • US$4.99
    • US$5.16